pro2 & multiple encoder processes

I was just trying to get this set-up on my new p.c. and having rebuilder 1.08.1,procoder2 I can't get neither eclpro0.52 or the eclpro test build for dualdvdrb to give me multiple encoder processes functionality I just keep getting error, something about invalid preset's this happened on two different source files I thought this was already addressed but a search left me puzzled (lost all my book marks). any one got it up and running?? is it possible? thnx 4 any feedback

Last time I (accidentally) tried ECLPro wouldn't run two instances simultaneously. That was probably an old version though. Even if it works now, I'm not sure ProCoder itself is able to run two instances.

When using the tool dualdvdrb and the test eclpro robot made for it. I remember it ran fine I just didn't see any increase w/ the p4 now that I got a 920 I was ready to test again but with rb's built in settings I just can't get it to go right! preset's are invalid? that's all I get, I thought I read about ti somewhere here but I continually search and can't find the answer?? *edit=fat fingers =)

i've got it working fine though with a ht the gain is very little maybe 7-10% at best. I didn't install anything new other than updating to 1.08.1 and then checking the box in settings for m.e.p. I would suggest getting procoder to run normally 1st. and not using anything not in the 1.08.1 full install

I saw that error too when I first implemented it. There is some kind of timing problem involved with the dual processing mode of ProCoder -- because you could run the same job twice and get it one time but not the other. It appeared that the two processes were trying to access something at the same time. So I added a minimal delay time separation to ensure no two ProCoder processes would start at exactly the same time. On my system it stopped the error from occurring. Frankly, I don't really know enough about ProCoder to even come close to calling myself expert in it -- I'm not even sure when, how, or why the "presets" are loaded...

it may be the source,exorcism of emily rose R1 here is what happened while using cce instead - Creating M2V for VTS_01 segment 13 - Creating M2V for VTS_01 segment 14 - Creating M2V for VTS_01 segment 15 - Creating M2V for VTS_01 segment 16 - Creating M2V for VTS_01 segment 17 - Creating M2V for VTS_01 segment 18 - Creating M2V for VTS_01 segment 19 - Creating M2V for VTS_01 segment 20 - Creating M2V for VTS_01 segment 21 -- V01002100001022 no .M2V, retrying. - Creating M2V for VTS_01 segment 21 - Creating M2V for VTS_01 segment 22 - Creating M2V for VTS_01 segment 23 - Creating M2V for VTS_01 segment 24 it don't look like a problem but the thing w/ procoder2 happened w/ walk the line as well so now I'm all kinda confused!

I'm investigating the problem. @l8nights I've sent you an email.

just got the message and hope we can work this out it's getting to me not having procoder on the new dual core. check your inbox =)

these things didn't seem to help me maybe the ram is the issue on the new p.c. as it's ddr2 I got it set to 4-4-4-12 but that's about as low as I can push it or so I've read! I was just able to get quite a large file (8+gb's) do-si do'ed ( three stepped) in 135 mins using procoder 2.04 building iso's w/ the new 920@3.6ghz, that's a big step from my ole p4 3.0's times

If there is a user which can repeat the error, I could send him by email a couple of EclPRO versions to check if we can solve. Send me email by PM.